Plumbing Basics: The First Step for Bathtub Installation
Plumbing Basics: The First Step for Bathtub Installation
Blog Article
What're your beliefs about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Mounting a bathtub isn't precisely brain surgery, yet it does require strong plumbing, carpentry, as well as sometimes, tiling skills. Replacing an old bathtub with a brand-new one is also a reasonably challenging task. If the old tub is readily available, the job can relocate easily; if you need to open up a wall surface to get rid of the old bathtub as well as position the brand-new bathtub, the job is much harder. In either case, the job is within a house handyman's skills, although you will need a helper to move out the old bathtub as well as set in the new one. See to it you have qualified on your own for the job as well as are comfortable attempting it. Instead of hiring a specialist to take over a halfway-completed task, it is much better to consider utilizing one before you begin. Opportunities are you may require an expert plumber to make tube links.
This write-up will assist you set up a brand-new tub in your bathroom if you have currently purchased a brand-new tub and also don't require to transform the plan of your previous water system pipelines.
Your tools and product checklist need to consist of the following:
Getting ready for the Setup
Firstly, the supporting structure supplied with the bath needs to be fitted (if needed) according to the maker's directions. Next, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is essential to make certain that if the tap features a plastic washing machine, it is fitted between the bath as well as the faucets. On a plastic bath, it is likewise practical to fit a sustaining plate under the taps system to avoid stress on the bath tub.
Fit the adaptable tap adapters to the bottom of both taps using 2 nuts and also olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet via the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Ensure you make use of every one of the supplied washers.
Link the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom should now prepare to be suited its final placement.
Removing Old Taps
If you need to change old faucets with brand-new ones as a part of your installation, then the first thing you should do is separate the water supply. After doing so, turn on the faucets to drain pipes any water remaining in the system. The procedure of eliminating the existing faucets can be quite troublesome as a result of the restricted access that is usually the instance.
Use a basin wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipelines to the faucets. Have a cloth prepared for the staying water that will certainly come from the pipes. As soon as the supply pipelines have been removed, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the single faucets from transforming during this procedure. When the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleaned of any kind of old sealing compound.
Prior to moving on to fit the new taps, compare the pipe connections on the old taps to the brand-new taps. If the old faucets are longer than the new taps, after that a shank adapter is needed for the new taps to fit.
Installing the Bathtub
Making use of the two wooden boards under its feet, place the bathtub in the required position. The wood boards are helpful in equally spreading the weight of the tub over the location of the boards as opposed to focusing all the weight onto 4 tiny points.
The next objective is to make sure that the bath tub is leveled all round. This can be accomplished by checking the spirit level as well as readjusting the feet on the bathtub up until the level reviews level.
To mount taps, fit all-time low of the furthest flexible tap connector to the ideal supply pipeline by making a compression sign up with; then do the exact same for the various other faucet.
Switch on the water and also examine all joints as well as brand-new pipework for leaks and tighten them if needed. Fill the tub and additionally inspect the overflow electrical outlet as well as the normal outlet for leaks.
Ultimately, take care of the bathroom paneling as defined in the producer's user's manual. Tiling as well as sealing around the tub ought to wait until the bathtub has actually been used a minimum of when as this will settle it right into its last placement.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will certainly require a plastic port to prevent damages to the string. One end of the port fits on the plastic tail of the tap and the various other end supplies a link to the current supply pipelines.
If you require to fit a monobloc, then you will call for reducing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, place the tap in the installing hole in the bath/basin making sure that the washers remain in place between the tap and the sink. Safeguard the faucet in place with the maker offered backnut. As soon as the tap is safely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with normal tap ports. The previous type ought to be linked to the tap finishes initially, tightening just by hand. The supply pipes can later be connected to the other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bathtub
In the location where the bathroom satisfies the tile, it is necessary to seal the accompanies a silicone rubber caulking. This is very important as the installation can relocate sufficient to break an inflexible seal, creating the water to permeate the wall between the bath as well as the tiling, bring about issues with wetness and feasible leaks to the ceiling below.
You can select from a variety of coloured sealers to assimilate your fixtures and fittings. They are sold in tubes and also cartridges, as well as can securing spaces up to a size of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of soaked paper or soft rope. Keep in mind to constantly load the bathtub with water before securing, to enable the movement experienced when the bathtub remains in use. The sealant can fracture fairly very early if you do not take into account this motion before securing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise easily available on the marketplace. It is recommended to fit the floor tiles utilizing waterproof or waterproof adhesive as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I found that page about Installing A Bathtub while exploring the web. For those who enjoyed our blog post please make sure you remember to share it. I am grateful for your time. Visit again soon.
Click Here! Report this page